Automatic Backwash Filters for Philippine Cooling and Process Water

Industrial lighting, valves, filtration and instrumentation for the Philippines since 2005sales@ultrapowerindustrialinc.com

Automatic Backwash Filters for Philippine Cooling and Process Water

November 13, 2026By Khalil Joseph Banares6 min read

Cooling water and process water systems in the Philippines draw on rivers, seawater, reservoirs and municipal supplies that all carry suspended solids. Left unfiltered, these solids foul heat exchangers, block spray nozzles, wear pumps and reduce plant efficiency. Manual cartridge and bag filters can handle small flows, but they demand frequent attention, and the cleaning labour and downtime add up quickly.

Automatic backwash filters address this by cleaning themselves while the system keeps running. This guide explains how they work, where they fit, how to size them and what to check before purchase. Ultra Power supplies Bollfilter equipment in the Philippines and can support enquiries from industrial and utility customers.

How an Automatic Backwash Filter Works

Water enters the filter housing and passes through a screen element, leaving solids on the screen surface. As solids accumulate, the pressure difference across the screen rises. When a preset differential pressure or time interval is reached, a cleaning cycle starts. A backwash arm or nozzle system reverses the flow locally across part of the screen and discharges the dislodged solids through a drain valve, while the rest of the screen continues to filter.

Because the cleaning is local and short, the system delivers continuous filtered flow without interruption. This is why automatic filters suit plants that cannot stop for cleaning.

Typical Applications

Automatic backwash filters are used for power plant cooling water, industrial cooling circuits, seawater intake protection, process water for food and beverage plants, irrigation systems and pre-filtration ahead of membrane systems such as reverse osmosis. They are well suited to water with moderate solids loading and to systems where continuous flow and low labour input are priorities.

They are less suited to fluids with very high solids loads, sticky or oily contamination, or heavy fibre content unless the design is matched to that duty. Provide water analysis data so that the right filter and screen can be proposed.

Sizing and Selection Inputs

Gather the required flow rate, the operating pressure, the water source, the nature and concentration of solids, the required filtration degree, the permissible pressure drop and the temperature. The filtration degree should reflect the downstream equipment, such as the particle size tolerated by spray nozzles or heat exchanger tubes.

Choose the housing and screen materials to suit the water. Seawater and brackish water call for corrosion-resistant materials. Ask the supplier about the flow range of each model and the backwash water volume per cycle so that you can plan the drain capacity.

Backwash Water and Drain Planning

Every cleaning cycle sends a small volume of water and solids to the drain. Plan a drain line of adequate size, discharged to a location where the backwash stream can be handled in line with environmental requirements. In inland or water-scarce locations, consider returning backwash flow to a treatment or settling stage.

Check that the drain pressure is low enough for effective backwashing. A backed-up or restricted drain reduces cleaning performance.

Controls and Instrumentation

The control unit starts a cleaning cycle based on differential pressure, time, or both. A differential pressure switch or transmitter is the usual trigger. Confirm the power supply and signal requirements, and whether the filter will send alarms and status to the plant control system. Integrate a high differential pressure alarm to flag a screen that is not cleaning properly.

Installation Guidelines

Install the filter where there is room for maintenance access to the screen and the drive. Provide isolation valves and a bypass if continuous supply must survive maintenance. Fit pressure gauges at the inlet and outlet. Support the weight of the filter independently from the pipework. In coastal sites, protect motors and control cabinets against humidity and salt air with correct enclosures and coatings.

Maintenance Routine

Inspect the screen, seals and backwash mechanism at scheduled intervals. Check the drain valve action, the drive motor and the differential pressure measurement. Watch for rising cleaning frequency, which signals a change in water quality or a problem with the screen. Keep spare seals and a spare screen on site for critical duty.

Manual versus Automatic Filtration

Factor Manual Cartridge or Bag Automatic Backwash
Operation Stops for cleaning or replacement Cleans while in service
Labour Frequent attention Minimal
Consumables Ongoing cartridge or bag cost Reusable screen
Best fit Small flows, low solids Larger flows, continuous operation
Water use None for cleaning Small backwash volume per cycle

Automatic Backwash Filter Checklist

  • Flow rate, pressure and temperature recorded
  • Water source and solids analysis available
  • Required filtration degree matched to downstream equipment
  • Housing and screen materials suit the water
  • Drain line size and discharge location planned
  • Control trigger defined: differential pressure, time or both
  • Power supply and plant control signals confirmed
  • Isolation valves, bypass and gauges provided
  • Maintenance access and spares planned

Protecting Downstream Equipment

The value of an automatic filter is measured downstream. Heat exchanger tubes stay cleaner, spray nozzles keep their pattern, pumps wear more slowly and membranes last longer. When you justify the investment, compare the filter cost with the cost of a single tube bundle cleaning, an unplanned shutdown or a replacement set of membranes. Many plants find that one avoided event covers a large part of the filter cost.

Record water quality before and after installation, such as turbidity and differential pressure across the downstream equipment. This evidence helps the operations team defend the filter in future budget reviews.

Frequently Asked Questions

Does an automatic backwash filter interrupt flow?

No. Cleaning is local to a section of the screen, so filtered flow continues during the cycle.

What causes frequent backwashing?

A change in water quality, higher solids load, a damaged screen or an inadequate drain can all raise cleaning frequency.

Can these filters be used with seawater?

Yes, when built with corrosion-resistant materials suited to seawater duty.

How much water does the backwash use?

The volume is small compared with the main flow, but it depends on the model and cycle frequency. Request the figure from the supplier for drain planning.

Related Reading

Contact Ultra Power for Inquiries

Ultra Power supplies Bollfilter automatic filtration equipment for Philippine plants and utilities, and can help you define the flow, filtration degree and materials that suit your water. Please contact Ultra Power for inquiries, and our engineering team will respond with practical guidance for your project.

Need a quotation or technical assessment?

Send the specifications. We respond within one business day.

Request Free Assessment

Download Our Free Industrial Lighting Compliance Guide

A complete reference for Philippine plant engineers and procurement officers.

Download Free Guide

Get the Ultra Power Company Profile 2026

Our products, brands, industries served and track record since 2005.

View Company Profile (PDF) →
© 2026 Ultra Power Industrial Resources, Inc. | Unit 105 Teylan Building, 6917 Washington St., Makati CityContact